Studi Kekuatan Sambungan Batang Tarik Pelat Baja Dengan Alat Sambung Baut

  • Mery Silviana Program Studi Teknik Sipil, Universitas Al Muslim
Keywords: Tension member, steel plate, bolt connection

Abstract

Steel as one of construction materials has several advantages compared to other construction materials. One of the advantages is it can withstand large tensile loads compared to wood and concrete. This research was conducted to find out the strength of the connection of two-faced steel plate tension member with bolts connection through experiment and compare it with theoretical calculations by using Allowable Stress Design (ASD) method. The focused structure is a two-faced connection tension member that is connected using bolts. Steel plated that used in this research are 8 mm and 10 mm thickness with bolt sizes Ø ¼ ", Ø 3/8" and Ø ½ ", each connection using three bolts as connector. The testing of the tension member connections in the laboratory is carried out by gradually loading the tensile load until the tensile member reaches the ultimate load. The results of experimental and theoretical research found that theoretical calculation of tensile strength smaller than tensile strength done experimentally.

Downloads

Download data is not yet available.

References

[1] Anonim, 1980, American Institure of Steel Construction (AISC), Eight Edition, 400 North Michigan Avenue Chicago, Illinois

[2] Anonim, 1981, Annual Book of ASTM Standard, Part 10, E-8, Standard Methods of Tension Testing og Metalic Materials, 1916 Race St., Philadelphia

[3] Anonim, 1983, Peraturan Perencanaan Bangunan Baja Indonesia (PPBBI), Yayasan Lembaga Penyelidikan Masalah Bangunan, Direktorat Penyelidikan Masalah Bangunan, Bandung

[4] Burhan, H., 1976, Konstruksi Baja I, Institut Teknologi Bandung, Bandung

[5] Buustraan, 1980, Daftar-Daftar untuk Konstruksi Baja. Cetakan kedelapan, Penerbit PT. Pradnya Paramita, Jakarta

[6] Gere dan Timoschenko, 1996, Mekanika Bahan Jilid I, Edisi kedua versi SI, Terjemahan Hans. J. Wospakrik, Penerbit Erlangga, Jakarta

[7] Gunawan, R., 2000 Tabel Profil Kontruksi Baja. Edisi Revisi, Cet. 14, Penerbit Kanisius, Yogyakarta

[8] Gunawan T dan Margaret S, 2002, Teori Soal dan Penyelesaian Konstruksi Baja I, Seri B Jilid I, Cetakan kedua, Penerbit Delta Teknik Group, Jakarta
[9] Marcus, S.H., 1981, Basic of Structural Steel Design, Reston Publishing Company, Virginia
[10] Salmon, C.G., dan John E. Johnson, 1997, Struktur Baja Jilid I, Desain dan Perilaku, Terjemahan Mc. Prihminto Widodo, Edisi kedua, Cet. IV Penerbit Erlangga, Jakarta
[11] Schodek, D.L., 1999 Struktur, Terjemahan Bambang Suryoatmono, Edisi kedua, Cet. I, Penerbit Erlangga Jakarta
[12] Spiegel L., dan George F. Limbrunner, 1991, Desain Baja Struktural Terapan, Terjemahan Bambang Suryoatmono, Penerbit PT. Eresco, Bandung.
Published
2017-12-31
How to Cite
[1]
M. Silviana, “Studi Kekuatan Sambungan Batang Tarik Pelat Baja Dengan Alat Sambung Baut”, JI, vol. 2, no. 2, pp. 75-80, Dec. 2017.